{"title":"1-post lifts","description":"\u003ch2 id=\"speakable-headline\"\u003eA 1-post lift raises the car where two posts won't fit\u003c\/h2\u003e\n\n\u003cblockquote id=\"speakable-summary\"\u003e\n\u003cp\u003e\u003cem\u003eWhat is a 1-post lift? It's a single lifting column that raises the vehicle from one long side, using lifting arms or runways. It takes up little floor space and leaves three sides clear. It's not the right pick for heavy SUVs, vans or jobs where you put a lot of force into the car.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\n\u003chr\u003e\n\n\u003cp id=\"speakable-definition\"\u003e\u003cstrong\u003e1-post lifts\u003c\/strong\u003e (single-post lifts) raise a complete vehicle on just one column that stands next to the parking bay. The car is carried either on arms at the lifting points or on runways under the wheels. Because the load hangs off to the side of the column instead of sitting between two posts, the leverage on the column decides how heavy the vehicle can be. Capacity reserve, ceiling height and foundation for every lift type are covered on the \u003ca href=\"\/en\/collections\/hebebuehne\"\u003eCar lifts\u003c\/a\u003e overview.\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree sides stay clear.\u003c\/strong\u003e The column stands on one long side; the base frame of the C-1.25 spindle lift is 1,600 mm wide. Front, rear and the opposite side stay open, and the doors on that side open all the way. For wheels, brakes, sills and wheel arches, that's exactly the access you need.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e2,850 mm of ceiling height for the car column.\u003c\/strong\u003e The C-1.25 column is 2,665 mm tall and lifts 2,500 kg to a maximum of 1,970 mm. The 2,850 mm is what you need just to stand the column up.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1,000 kg on runways for ride-on mowers and quads.\u003c\/strong\u003e The Monolift 1000 takes small vehicles up to 1,860 mm in about 30 seconds on a 230-volt power unit. The vehicle rolls up ramps onto the runways, so there's no hunting for lifting points.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003chr\u003e\n\n\u003cblockquote class=\"praxistipp\"\u003e\n\u003cp\u003e\u003cstrong\u003eDetailing1's tip from the shop:\u003c\/strong\u003e The questions we get are about lifting height, power and dimensions, sometimes only after the order is in. With a single post, one question comes first: does your car fit the arms? Find the four lifting points in the owner's manual, measure the distances between them lengthways and across, and hold them against the arm lengths of the C-1.25: 695 to 940 mm at the front and 580 to 760 mm at the rear. If your sill sits lower than 110 mm, the arms won't get underneath.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\n\u003chr\u003e\n\n\u003ch3\u003eOne column lifts from the side and leaves three sides clear\u003c\/h3\u003e\n\u003cp\u003eA 1-post lift picks the vehicle up from one long side only, carries it on arms or runways and leaves the front, the rear and the other flank free to get at.\u003c\/p\u003e\n\u003cp\u003eOn the Weber-Werke \"C-1.25\" spindle lift, four telescopic lifting arms sit on a carriage that runs up the column. The front and rear arms reach different distances; the exact lengths are in the tip above. They swing under the lifting points on both sides of the car, just like on a two-post lift. The difference: all four arms come from the same side. For you, that means the doors on the far side open without any restriction.\u003c\/p\u003e\n\u003cp\u003eWhat changes is the direction of the forces. On two posts the car hangs centrally between two supports; on one post it hangs off to the side. So the column doesn't just take the weight, it also takes a tipping moment, the leverage you get because the load hangs next to the foot of the column rather than above it. That's where the capacity and tipping limits of this lift type come from.\u003c\/p\u003e\n\u003cp\u003eThat still doesn't make a single-post lift a stripped-down two-post. It's its own answer to tight space: two posts need a drive-in path between the supports, while one post stands beside the bay and you simply pull up next to it. If you've got a narrow garage or a bay with no room for two posts, this is how you get a lift in there at all.\u003c\/p\u003e\n\n\u003ch3\u003eOne name covers three very different machines\u003c\/h3\u003e\n\u003cp\u003eThe term 1-post lift covers three designs: the fixed column with lifting arms for cars, the mobile column and the column with runways for small vehicles.\u003c\/p\u003e\n\u003cp\u003eThe fixed column stands on a base frame and is anchored to the floor; Weber sells its own heavy-duty anchor kit for the C-1.25. It's driven electromechanically by a spindle: a vertical threaded rod 45 mm in diameter with a load nut running on it, like a nut on a bolt. In plain terms: no hydraulic cylinder and no hydraulic oil in the lifting system, but a load nut that Weber stocks as a spare part and that beds in over time.\u003c\/p\u003e\n\u003cp\u003eWeber gives a five-year warranty on the spindle and load nut of the C-1.25, but only if an authorised service partner installs and services it. That's more than small print. If you put the column up yourself, you give up that warranty. So plan the installation at the same time as the purchase instead of deciding after delivery.\u003c\/p\u003e\n\u003cp\u003eThe mobile column has a running gear in its base and is pulled to the job like a pallet truck. One model of this type weighs about 720 kg, and its manufacturer puts two rules for moving it in the manual: only on level ground and never with a vehicle raised. If you're searching for a mobile single-post lift, this is the design you mean.\u003c\/p\u003e\n\u003cp\u003eThe third design doesn't carry the car at the lifting points but under the wheels. On the Weber-Werke \"Monolift 1000\", the vehicle rolls up self-folding ramps onto two runways that slide along a crossbeam. According to the manufacturer, it's meant for ride-on mowers, quads and special vehicles. The only thing it shares with the other two is the single column.\u003c\/p\u003e\n\n\u003ch3\u003eCapacity stops at 2,500 kg, and so does the lift at cars\u003c\/h3\u003e\n\u003cp\u003eThe C-1.25 car column carries 2,500 kg; with the reserve of about 20 percent from the car lift overview, it suits vehicles up to roughly 2.1 tonnes.\u003c\/p\u003e\n\u003cp\u003eThat matches the overview page: 2.5 tonnes is cutting it fine for a mixed fleet. Weber's own application pictograms rate the C-1.25 as suitable for cars and minibuses, conditionally suitable for long-wheelbase minibuses and unsuitable for vans. If you lift an estate today and a heavy EV in two years, size it for the later car.\u003c\/p\u003e\n\u003cp\u003eSingle-post lifts with 3.5 tonnes of capacity do get searched for. In this range the car column sits at 2,500 kg; if you need to lift more, you'll find the higher capacity classes among the two-post lifts. That's not a budget version, it's down to the design: the heavier the vehicle, the bigger the tipping moment a single column has to take from the side.\u003c\/p\u003e\n\u003cp\u003eThe manufacturer says the pictograms are only a guide, and not every model in a vehicle class can be picked up. What decides it is geometry: how low the arms swing in and how far they reach. How to check both on your car beforehand is in the tip above. A light car doesn't help if the arms won't fit underneath.\u003c\/p\u003e\n\u003cp\u003eShort cars have the opposite problem. The lifting points sit close together, and the arms still have to hit them cleanly. In Z4 and Mini forums, exactly this question comes up before people buy. Then there's weight distribution: on lifts up to 3.5 tonnes, the German statutory accident insurance says the front-to-rear split should be between 3:2 and 2:3, with the heavier end of the vehicle on the shorter lifting arms.\u003c\/p\u003e\n\u003cp\u003eAdd space and power to that. The C-1.25 needs 2,850 mm of ceiling height and runs on 400-volt three-phase power at 3.6 kW. Check before you order that three-phase is available where it's going. The ceiling height is what the column needs to be stood up. How high you can raise the car in your space, and whether you can stand upright under it, you work out from the vehicle height; the calculation is on the \u003ca href=\"\/en\/collections\/hebebuehne\"\u003eCar lifts\u003c\/a\u003e page.\u003c\/p\u003e\n\n\u003ch3\u003eKeep the load close to the column\u003c\/h3\u003e\n\u003cp\u003eBecause the load hangs off the side of the column, the centre of gravity decides how stable it stands, and brute-force jobs or heavy parts coming off shift it the wrong way.\u003c\/p\u003e\n\u003cp\u003ePicture a full bucket held at arm's length. The further it is from your body, the heavier it feels, even though it weighs the same. That's exactly how the tipping moment acts on the column. For you, that means: set the car on so its centre of gravity sits as close to the column as possible, and don't pull the arms out further than you need to.\u003c\/p\u003e\n\u003cp\u003eIt gets critical when the centre of gravity moves during the job. When a gearbox, an axle or a heavy exhaust system comes out, the weight shifts inside the car. The manual of one mobile column warns explicitly that the vehicle can tip. Jobs like that you plan on two posts, not one.\u003c\/p\u003e\n\u003cp\u003eFor lifts, the German statutory accident insurance names one type of accident that matters here in particular: the vehicle gets pulled off because someone heaves on a seized bolt. On a single post, that jolt also acts sideways. So crack seized wheel bolts while the wheels are still on the ground.\u003c\/p\u003e\n\u003cp\u003eAfter the first lift to a low height, do a shake test: rock the car briefly and check that all four pads sit cleanly on the lifting points. Only then go up to working height. You stand under the car once the lift has stopped, never while it's going up or down.\u003c\/p\u003e\n\u003cp\u003eAccess has its limit too. The arms all come from one side and sit under the car. Users in forums report that arms and crossbeam get in the way on exhaust, prop shaft and lines down the middle of the car. For work on wheels and flanks, that's no problem.\u003c\/p\u003e\n\n\u003ch3\u003eThe C-1.25 lifts the car, the Monolift 1000 the ride-on mower\u003c\/h3\u003e\n\u003cp\u003eThe range here covers two separate jobs: the spindle column for cars and the runway column for ride-on mowers, quads and special vehicles, both from the Weber-Werke Expert series.\u003c\/p\u003e\n\u003cp\u003eThe \u003ca href=\"\/en\/products\/weber-werke-weber-expert-serie-1-saeulen-spindel-hebebuehne-c125\"\u003eWeber-Werke \"C-1.25\" spindle lift\u003c\/a\u003e goes up to a maximum of 1,970 mm in 45 seconds. It's controlled with push buttons, so you can set the height precisely. An automatic safety stop halts the carriage if there's an obstacle in the way on the way down. The rear arms have trays for tools. It's the column for working on the wheels and flanks of a car.\u003c\/p\u003e\n\u003cp\u003eThe \u003ca href=\"\/en\/products\/weber-werke-weber-expert-serie-1-saeulen-hebebuehne-monolift-1000\"\u003eWeber-Werke \"Monolift 1000\" runway lift\u003c\/a\u003e works with a 230-volt hydraulic power unit rated at 2.2 kW. The runways are 350 mm wide and 1,830 mm long, and the drive-on height is 75 mm. It's operated with a 24-volt dead-man control: the lift only moves while you hold the button and stops the moment you let go. The safety latches lock automatically.\u003c\/p\u003e\n\u003cp\u003eCapacity and runway width show what the Monolift is built for. We had an enquiry from a municipal depot that wanted to get ride-on mowers up to working height with it. Measure the track width and wheelbase of your machine against the sliding runways and their length first. If both fit, you're done kneeling next to the mower deck.\u003c\/p\u003e\n\u003cp\u003eFor floor space, it's not just the 2,830 mm tall column that counts on the Monolift. With ramps the runway measures 2,010 mm, and the whole lift takes up 2,700 by 1,900 mm. Allow room in front of the ramps to drive on as well. It weighs 400 kg; the C-1.25 comes in at 630 kg.\u003c\/p\u003e\n\u003cp\u003eHydraulic on the Monolift means there's oil working in the system. Which type you top up with is in the lift manufacturer's manual; the differences are explained on the \u003ca href=\"\/en\/collections\/hydraulikoel\"\u003eHydraulic oil\u003c\/a\u003e page. The C-1.25 doesn't need hydraulic oil but lubrication on the spindle and load nut, and Weber has its own spindle oil for that. The rest of the manufacturer's range is under \u003ca href=\"\/en\/collections\/weber-werke\"\u003eWeber-Werke\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch3\u003eGive up one side of the car and you get your floor space back\u003c\/h3\u003e\n\u003cp\u003eOne post is enough when space is tight, you're lifting a car up to about two tonnes and the work is on wheels, brakes, sills or wheel arches.\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYour job\u003c\/th\u003e\n\u003cth\u003eLift type that fits\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eWheels, brakes, sills, wheel arches on a car in a tight space\u003c\/td\u003e\n\u003ctd\u003eCar column such as the C-1.25\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eGarden tractor, ride-on mower, quad\u003c\/td\u003e\n\u003ctd\u003eMonolift 1000 runway column\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eGearbox, exhaust, centre of the underbody, heavy vehicles\u003c\/td\u003e\n\u003ctd\u003e2-post lift\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eClear access all round, work at wheel height\u003c\/td\u003e\n\u003ctd\u003eScissor lift\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTwo wheel changes a year\u003c\/td\u003e\n\u003ctd\u003eTrolley jack with axle stands\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eIf you're working on the gearbox, exhaust or the middle of the underbody, taking off heavy parts or lifting SUVs and vans, the car belongs on \u003ca href=\"\/en\/collections\/2-saeulen-hebebuehnen\"\u003e2-post lifts\u003c\/a\u003e. If you want clear access all round and wheel height is enough, \u003ca href=\"\/en\/collections\/scherenhebebuehnen\"\u003escissor lifts\u003c\/a\u003e fit. If it's only the wheel swap in spring and autumn, a \u003ca href=\"\/en\/collections\/wagenheber\"\u003etrolley jack\u003c\/a\u003e with axle stands does the job and saves you the fixed kit.\u003c\/p\u003e\n\u003cp\u003eThe column sits between those cases. It's the lift for anyone who wants to look after and maintain a car but hasn't got a double garage to spare. Flushing out wheel arches, checking brakes, protecting sills: you do it standing up, with the door on the far side free, while the rest of the space stays usable.\u003c\/p\u003e\n\u003cp\u003eThe first lift takes longer than you think. Lining up the arms, setting the pads under the lifting points, rocking it at low height, then going up: that takes a few minutes at first and becomes second nature after a few goes. That's part of it and says nothing about whether the column was the right call.\u003c\/p\u003e\n\u003cp\u003eTwo things stay true even for wheel and flank work: one side of the car is always taken, and the car column tops out at 2,500 kg. Accept that, and you get a lift on the footprint of one parking bay. Within that limit, the lifting points and sill height of your car decide whether the column fits, not the tonnes on the rating plate.\u003c\/p\u003e","products":[],"url":"https:\/\/detailing1.it\/en\/collections\/1-saeulen-hebebuehnen.oembed","provider":"Detailing1","version":"1.0","type":"link"}