ZviZZer Applicator Cloths white Applicator Towels 150 pieces

Lay your coating onto the paint clean and lint-free

What are the ZviZZer Applicator Cloths white? Soft, lint-free suede cloths in a pack of 50 that let you lay ceramic coatings and sealants down thin and even. The short, dense fibre soaks up little product and drops no lint into the fresh film. They're a consumable, not a buffing cloth for removal and not a cleaning cloth.

The ZviZZer Applicator Cloths white are soft, lint-free applicator towels from ZviZZer made of short-pile suede microfibre, sized 15 by 10 centimetres and supplied as a pack of 50. You wrap one cloth around the applicator block and put a few drops of coating on it — the dense, low-pile fibre spreads the product in a thin, even wet film without soaking it up and without leaving fibres in the film. That's how you lay a coating down in a controlled, streak-free way.

• Lint-free instead of fibres in the coating. Unlike a fluffy microfibre towel, the short-pile suede fibre drops no lint that would otherwise lodge in the curing coating. Just 1 trapped fibre in the finished film forces you to re-polish the whole section. That's exactly what these cloths are made for — not drying or cleaning.
• 50 cloths as a consumable. The pack of 50 lasts for plenty of coating jobs, since you swap the cloth roughly every three to four sections. Per car you'll go through several cloths depending on the coating and the state of the paint, because a cloth that's gone tacky no longer lays down cleanly.
• 15 by 10 centimetres wrapped around the block. The format fits around the applicator block and gives you three usable faces. The low pile soaks up little product, so more coating ends up on the paint instead of disappearing into the cloth. Twelve to eighteen drops are enough depending on the size of the panel.

Detailing1's tip from the shop: The most common mistake when laying down a coating is dragging the same cloth across the whole car. As soon as the coating dries into the cloth, it just pushes product along in front of it and pulls streaks instead of an even film. Put twelve to eighteen drops on the cloth, work in straight, overlapping passes plus a cross pass, and grab a fresh one after three to four sections. With us, a cloth used too long on the bonnet left visible high spots that we had to polish back.

Cloth around the block coating on apply in passes

Wrap an applicator cloth around the applicator block, put twelve to eighteen drops of coating on the cloth face and apply in straight, overlapping passes, then once across as a cross pass for an even film.

The block gives the soft cloth the even pressure it needs so the coating goes onto the paint in a thin wet film. Wrap the cloth tightly around the applicator block so no creases pull streaks. You need paint that's clean, polished and degreased with isopropanol — on a greasy surface the coating levels unevenly.

Work panel by panel and watch the film: when the wet trail goes matte, the coating has flashed off and you buff it out with a fresh, soft microfibre cloth. Swap the applicator cloth after about three to four sections, as soon as it feels tacky. Wash the cloths before first use and work with them dry.

Yes for applying no for buffing out

The applicator cloths are a pure application tool for liquid coatings and sealants — to take off the flashed film and buff it out you need a separate, soft microfibre cloth, not the suede cloth.

Their core job is the controlled coating application: a thin, even wet film with no trapped fibres. On a freshly polished and degreased door you lay a clean layer of the Graphene Ceramic Coat ceramic sealant with block and cloth, which the suede spreads evenly instead of pulling it off like an absorbent towel would.

The limits are clear: if a liquid coating needs to go on thin and lint-free, then the suede applicator cloth. If the dried film needs taking off or buffing to a high gloss, then a fluffy microfibre cloth. A cloth that's gone tacky is spent and should be swapped, not washed out and reused — otherwise it pulls streaks into the next section.

For the coating user not for the quick wash

The applicator cloths are the right call when you apply a ceramic coating or a liquid sealant yourself and need an application medium that swallows little product and leaves no lint in the film.

They're the consumable in the coating workflow and part of our accessory range. Block and cloth go together: the block brings the pressure, the cloth the lint-free face. With the pack of 50 you've got enough in reserve to switch to a fresh cloth in time on every job, instead of pushing on with a tacky one and risking high spots.

They're less suited to anything other than applying: not for drying the car, not for cleaning, not for buffing out. If you only wash your car and never apply a liquid coating, you don't need them — they're a specialist tool for sealing.

The one thing most people underrate: with a coating, the cloth decides half the result. A fresh, lint-free suede cloth per section costs a few cloths more, but it saves you re-polishing streaks and trapped fibres that otherwise stay in the cured coating for good. That's exactly why there are 50 in the pack and not five.

Application of ZviZZer applicator cloths white

From degreased paint to a uniform coating film

Before application, the paint must be prepared: washed, decontaminated, polished, and degreased with isopropyl alcohol. The coating will not fully adhere to a greasy or dirty surface and will level unevenly; the best cloth cannot change that.

Wrap an applicator cloth tightly around the applicator block so that no wrinkles cause streaks. Apply twelve to eighteen drops of coating to the cloth surface and apply in straight, overlapping paths, then once more crosswise in a cross-hatch pattern. This creates a thin, even wet film without gaps.

Work component by component and observe the film. If the damp trail turns matte, the coating has flashed off, and you should remove it with a fresh, soft microfiber cloth and polish it to a streak-free finish. Change the applicator cloth after about three to four sections, as soon as it feels tacky.

The low suede fiber absorbs little product, so more coating ends up on the paint than in the cloth. This is precisely why these cloths are superior to standard microfiber cloths when applying the Graphene Ceramic Coat — they distribute rather than absorb.

Notes: The applicator cloths are purely for application; they are not polishing or cleaning cloths. Wash the cloths before first use and always use them dry. Coating that has cured in the cloth makes it unusable — use a fresh one, do not continue using it, otherwise streaks and high spots will occur. Store the cloths in a dry, dust-free place. The pack of 50 provides enough reserve to change in time for every application.